Dilas FT1800 Máy đo khoảng cách Delta Sensor

Giá bán: Liên hệ

Hãng sản xuất: Delta Sensor

Danh mục: Máy đo khoảng cách

Nhà cung cấp: Jon & Jul Viet Nam

Xuất sứ: Pháp

Bảo hành: 12 tháng

Ứng dụng sản phẩm: Thiết bị tự động hóa

Gọi lại cho tôi

Liên hệ tư vấn

Hưng

hung@jon-jul.com

0374830598

live:.cid.7db5d206f62020e9

Thông tin sản phẩm
Thông số kỹ thuật

Dilas FT1800 Máy đo khoảng cách Delta Sensor

1. Giới thiệu

- Dilas FT1800 Máy đo khoảng cách Delta Sensor Hiện đang được Cty Jon-Jul phân phối rộng rãi tại thị trường Việt Nam.

2. Thông số kỹ thuật

Laser Distance Meter with Communication
Dilas FT1800

Digital communication: Profibus-DP, Profinet, Ethernet Modbus TCP, EtherNet/IP
High temperature targets - Long range - High accuracy
Easy setup and installation
Design for difficult conditions

Introduction

The Dilas FT1800 is a digital, high resolution, non-contact laser distance measurement or detection sensor. The target may be hot or cold, stationary or moving. Dilas FT1800 measures on all non-shiny surfaces.

The operation of the Dilas FT1800 is based on time-of-flight measurement. The sensor calculates the distance of the target surface using the time of flight of visible laser light pulses.

The measurement is delivered on an analogue output or on the digital communication.

Presentation

The Dilas FT1800 is an autonomous sensor mounted in compact aluminium housing, IP66. The sensor can be ordered with mounting bracket or mounting stand and water-cooling jacket.

A digital display indicates the measured distance and two LED indicate status of sensor.
For the models with digital communication, two additional LED indicate the communication link status.
The sensor can work as a standalone unit: in that case, the setup is made from the control panel at the back of sensor.

Features and benefits

Two internal laser modules: 1 mW or 5 mW, for a better measuring margin on very hot targets or in difficult conditions
Target temperature: up to 1300 °C
Analogue output : 4-20 mA
Digital communication :
Visible red laser beam
Autonomous sensor: ready to use, no calibration required
Integrated 5 digits display
Easy sensor setup with pre-set distances selection
Extended configuration of customized measuring range and response time
Special modes (‘Time’) optimized for: Detection / Tracking / Averaging / Fixed Sampling
Optional Water cooling & air purging – Optional Heat Shield & additional cooling plate

Applications

The Dilas FT1800 offers different modes optimized for different applications. The setup of the mode is very easy and quick via the back panel selector in the ‘Time” position. Be sure to select the mode adapted to your own situation:

Auto mode gives measurement as soon as it is available with the best accuracy. The measuring time is not fixed and depends on the measurement conditions: reflectivity of the target, distance. If the measurement is not possible, the sensor delivers an error code after maximum 6 seconds.
Fixed sampling time allows user to get a repeatable and fixed measuring time: the target needs to be always measurable within this fixed time to use this mode, otherwise an error code may appear.
Tracking mode: when the target is moving in the axis of the sensor, this mode is recommended and provides better results and refreshment time.
Detection mode is interesting for applications where product or background is not measurable within a fixed time.
Instead of freezing the detection output and the measurement value like for other modes, the FT1800 in detection mode will release the output and measurement after the fixed time.
Average mode makes a moving average x2 or x4 of the last values, to get a more stabilized and accurate measurement.

Accessories

Heat shield to protect sensor from direct radiations.

Only compatible with Mounting stand & cooling jacket (FT18••-J• models).

Additional cooling plate

Only compatible with Mounting stand & cooling jacket (FT18••-J• models).

Accessories, remote display unit (for FT18•4 only)

Remote Display unit (connection to 1 or 2 sensors) with 1 dimension calculation (connection to 2 sensors, static product)

For display of of sensors measurements, status and error code. On the operator pulpit, for cut to length application for example, or in case the access to the sensor is difficult or dangerous.

Provides calculation and display of 1 dimension: width, length, thickness. Calibration procedure (distance between sensors and correction coefficients).

Dimension value and calibration parameters stored in each sensor for access through Modbus TCP.

Delivered in a complete junction box including a 7" colour display, an Ethernet switch, connectors for sensors power supply & I/O, terminal blocks and a 115/230VAC to 24 VDC power supply.